KraftMaid Home Additions & ADU Nationwide

KraftMaid Home Additions & ADU: The Santa Clarita Owner’s Guide

KraftMaid cabinet systems in Santa Clarita home additions and ADUs typically run $45,000-$130,000 installed, depending on whether you’re extending existing KraftMaid runs into a new addition or specifying fresh for a detached ADU. We stock KraftMaid-compatible cabinet configurations, hardware, and finishing systems on our Santa Clarita warehouse shelf, and most ADU kitchenette packages can be spec’d and quoted within 48 hours. The failure usually starts small: a drawer glide catching in a guest unit, a hinge sagging on a cabinet installed during the 2019-2021 boom when Santa Clarita saw a wave of garage conversions with tight timelines and looser inspection schedules.

Call (747) 294-3985

Which KraftMaid Models This Applies To

KraftMaid’s product lines split into three tiers relevant to Santa Clarita ADU work, and matching the right one to your existing install determines whether the new cabinets blend or clash.

• Canvas (formerly Allure): The thermofoil line common in 2016-2020 garage conversions. The white and grey tones yellow faster in Santa Clarita’s high-UV inland valley sun, especially on south-facing ADU windows. If your existing cabinets show surface cracking at the door edges, you likely have Canvas. Replacement doors are still manufactured, but the thermofoil cannot be field-repaired; the whole door must swap.
• Vantage: The painted wood line with a five-piece door. This is what we spec most often for new ADU builds in Santa Clarita because the paint holds up to heat cycling better than thermofoil, and the soft-close hinge cups are cross-compatible with Blum hardware, which we stock.
• Natural: The stained wood line, usually cherry or maple, found in higher-end additions off Bouquet Canyon and Sand Canyon. The stain lots vary year to year; if you’re extending a 2018 kitchen into a new addition, we order a sample door first and compare it under your existing LED lighting before the full run ships.

Identification is straightforward: open any upper cabinet and look for the foil label on the hinge side of the door, or the stamped code on the drawer box back. The first four digits are the series code (CANV, VANT, NATR). If the label is gone, measure the hinge boring pattern: 35mm cup, 3mm offset for Canvas and Vantage; Natural uses the same cup but a 0mm mount plate. Getting this wrong means new doors that won’t close flush. We verify this on every Santa Clarita site visit before ordering.

Rowan Construction Group Santa Clarita is an independent contractor and is not affiliated with KraftMaid Corporation. We source through authorized distribution and maintain our own stock of hardware and compatible finishing systems.

Signs Your KraftMaid Home Additions & ADU Is Failing

• Drawer boxes dropping or tilting. The particleboard drawer sides on pre-2020 Canvas lines swell at the dovetail joints when Santa Clarita’s dry winter air gives way to summer humidity. The drawer then racks in the opening and the glide rollers flat-spot. We replace with solid birch dovetail boxes that use the same glide holes.
• Doors hanging uneven or rubbing the frame. Hinge cups wallow out in MDF door stiles, especially on upper cabinets over ADU cooktops where grease vapor accelerates the breakdown. The Blum clip-top hinge is a 30-second swap if the cup is still round; if it’s oval, the door needs replacement.
• Thermofoil peeling at the seam. Santa Clarita’s 100°F-plus summer days in garage conversions without proper HVAC cause the adhesive to release. Once the edge lifts, it catches and tears. This cannot be glued back; the door or drawer front must be remanufactured.
• Adjustable shelf pins pulling out. The 5mm pressed-wood pin holes in economy lines lose grip after three to five years of loading. We drill and insert metal threaded inserts that accept standard shelf pins, a permanent fix we include when we reface or extend a run.
• Soft-close dampers failing. The hydraulic cylinder in the hinge arm leaks after roughly 50,000 cycles, or sooner in dusty Santa Clarita construction zones. The damper is a separate part from the hinge; we stock both Blum and KraftMaid-branded equivalents and match what’s on your existing cabinets.

Before

After

Replacement Cost & What’s Included

ADU and home addition work with KraftMaid cabinets in Santa Clarita falls into three cost bands based on scope, not guesswork.

The wide range on full packages reflects three variables: whether the ADU is detached (new electrical, plumbing, and HVAC routing) or attached; whether the foundation is slab or stem wall on Santa Clarita’s hillside lots; and whether the kitchenette is a straight galley or includes an island with pendant rough-in. Under Clause 1 of the Haven Standard, the written price we deliver before work starts includes all three of those line items separately, so you see where the money goes before you sign. No change proceeds without a signed change order, which is the discipline that has kept our projects within a few percent of the agreed cost across 4,000-plus jobs since 2007.

DIY or Call Us?

There’s a clear line between what a Santa Clarita homeowner can safely check and where the job turns into construction work that affects your permit status and safety.

What you can do: confirm the series code from the cabinet label, photograph the hinge cup and any damage, and measure the opening width and height. That information lets us pre-order the right parts before the first truck rolls. What you should not do: remove load-bearing upper cabinets in an ADU built under 2020 California ADU code, which may have seismic straps or fire-rated assemblies behind the boxes. The 2019 and 2021 code cycles added requirements for Santa Clarita’s Zone D seismic classification that aren’t visible until the cabinet comes off the wall. We pull the permit history before we touch a tool, and we document the existing condition with photos before we start, included as standard on every visit.

Call (747) 294-3985 to schedule your free estimate. We’ll review what you have, what needs to match, and what the written price looks like before anyone picks up a tool.

FAQs